Fast delivery
Get in as fast as 1 hour
It’s all local
Shop your favorites
Direct chat
Connect with shoppers
About
Details
8 x 2-1/2 inches. Fin/trim. T-10 bit included. Smallest heads for a clean look! AC257 treated lumber approved. IBC/IRC code compliant ESR no. 3201. Zero stripping: Recessed star drive. Trim head: Clean finish. Low torque: W-cut thread. No pre-drilling: Engineered zip-tip. Star Drive Head has 6 points of contact to eliminate strip-out. Trim Head is small for a clean finish. Patented W-cut thread design and zip-tip easily penetrates most material without drilling! Suggested uses: Deck rails; Exterior trim; Window jambs; Door jambs; Interior trim; Crown molding; Fine carpentry applications. Fin/Trim shear test results: Diameter: No. 8; 388 lbf avg. ultimate load. No. 9; 520 lbf avg. ultimate load. Please note the above stated values are ultimate load, tested after ASTM D 1761, Wood to Wood connection for sizes 2-1/2 inches to 3-1/8 inches in length. Climatek coated screws evaluated with 0.40 pcf ACQ-D and 0.40 pcf CA-B. Warranty: GRK warrants that this product is free from defects in material and workmanship. Grks' sole liability for any breach of this warranty shall be to replace this product or refund the purchase price. GRK shall not be liable for any fastening failure due to improper installation or defective substrate material. Building code approved, limited lifetime guarantee climatek all weather coating. www.grkfasteners.com. See ESR-3201 for actual recognized design loads. Visit (www.icc-es.org). Made in Taiwan.
Directions
For construction design purposes an applicable safety margin should be applied. For safety factor requirements in your area contact your local building official, architect or engineer. Test conducted in wood with a specific gravity 0.67.
Warnings
Failure to wear safety glasses with side shields can result in serious personal injury. Always wear ANSI compliant eye protection.
About
Details
8 x 2-1/2 inches. Fin/trim. T-10 bit included. Smallest heads for a clean look! AC257 treated lumber approved. IBC/IRC code compliant ESR no. 3201. Zero stripping: Recessed star drive. Trim head: Clean finish. Low torque: W-cut thread. No pre-drilling: Engineered zip-tip. Star Drive Head has 6 points of contact to eliminate strip-out. Trim Head is small for a clean finish. Patented W-cut thread design and zip-tip easily penetrates most material without drilling! Suggested uses: Deck rails; Exterior trim; Window jambs; Door jambs; Interior trim; Crown molding; Fine carpentry applications. Fin/Trim shear test results: Diameter: No. 8; 388 lbf avg. ultimate load. No. 9; 520 lbf avg. ultimate load. Please note the above stated values are ultimate load, tested after ASTM D 1761, Wood to Wood connection for sizes 2-1/2 inches to 3-1/8 inches in length. Climatek coated screws evaluated with 0.40 pcf ACQ-D and 0.40 pcf CA-B. Warranty: GRK warrants that this product is free from defects in material and workmanship. Grks' sole liability for any breach of this warranty shall be to replace this product or refund the purchase price. GRK shall not be liable for any fastening failure due to improper installation or defective substrate material. Building code approved, limited lifetime guarantee climatek all weather coating. www.grkfasteners.com. See ESR-3201 for actual recognized design loads. Visit (www.icc-es.org). Made in Taiwan.
Directions
For construction design purposes an applicable safety margin should be applied. For safety factor requirements in your area contact your local building official, architect or engineer. Test conducted in wood with a specific gravity 0.67.
Warnings
Failure to wear safety glasses with side shields can result in serious personal injury. Always wear ANSI compliant eye protection.
Common questions
Learn more about how to place an order here.
Then, when you arrive at the store of your choice, use the Instacart app to notify us. Depending on the store, a shopper or store employee will bring the groceries to your car, or you can pick them up at the designated area.
Learn more about pickup orders here.
- Delivery fees start at $3.99 for same-day orders over $35. Fees vary for one-hour deliveries, club store deliveries, and deliveries under $35.
- Service fees vary and are subject to change based on factors like location and the number and types of items in your cart. Orders containing alcohol have a separate service fee.
- Tipping is optional but encouraged for delivery orders. It's a great way to show your shopper appreciation and recognition for excellent service. 100% of your tip goes directly to the shopper who delivers your order.
With an optional Instacart+ membership, you can get $0 delivery fee on every order over $35 and lower service fees too.
Instacart pickup cost:
- There may be a "pickup fee" (equivalent to a delivery fee for pickup orders) on your pick up order that is typically $1.99 for non-Instacart+ members. Instacart+ membership waives this like it would a delivery fee.
- Pick up orders have no service fees, regardless of non-Instacart+ or Instacart+ membership.
Learn more about Instacart pricing here.
You can set item and delivery instructions in advance, as well as chat directly with your shopper while they shop and deliver your items. You can tell the shopper to:
- Find Best Match: By default, your shopper will use their best judgement to pick a replacement for your item.
- Pick Specific Replacement: You can pick a specific alternative for the shopper to purchase if your first choice is out-of-stock.
- Don't Replace: For items you'd rather not replace, choose "Don't replace" to get a refund if the item is out of stock.
Learn more about instructions for specific items or replacements here.
- Missing items
- Incorrect items
- Damaged items
- Poor replacements
- Early/late orders
If an order never came, or you get someone else's order, you can reach out to Instacart Customer Experience.